American Dynamics ADCIPE3312ICN Especificaciones

Part Number: 8200-2646-02 B0 VideoEdge IP Indoor Mini-domeInstallation & Operation GuideVersion1.6

10 Installation and Operation Guide 2.2 The USB function By connecting the IP camera with a PC via the USB connector, the IP camera can provide two

Installation and Operation Guide 11 2.3 PoE (Power over Ethernet) These technologies will enable the development of new networked appliances, by prov

12 Installation and Operation Guide 2.4 Power LED & IR LED Power setting The IR Board:  The J1 Jumper: Controls ON/ OFF function of the Powe

Installation and Operation Guide 13  The J2 Jumper: Controls ON/ OFF function of the IR LED IR Power Disable (Factory Default): Pin1 & Pin2 sho

14 Installation and Operation Guide 2.5 Lens adjustment Before adjusting the lens, the user has to remove the cover of the dome. 1) Loosen the screw

Installation and Operation Guide 15 2.6 Cover Attaching To attach the dome to the base, please do as steps (1) and (2). (1) Note that the protrusion

16 Installation and Operation Guide 2.7 Ceiling mounting When mounting the camera in the plywood ceiling, please follow steps (1) to (3).

Installation and Operation Guide 17 3. INSTALLATION Please follow the instructions and the diagram below to set up the system. 3.1 UPDATING SYSTEM SO

18 Installation and Operation Guide WARNING: 1. Don’t use the NTFS format in step 1. 2. Steps 1 to 3 have to be done on a PC. 3. Make sure the

Installation and Operation Guide 19 3.2 IP camera SD card Troubleshooting 1. Check if the SD card position is correct or not. Please refer to the m

20 Installation and Operation Guide 4. Network Configuration 4.1 Cable Connections Please follow the instructions below to connect your IP camera t

Installation and Operation Guide 21 4.2.2 Set IP Address You need to set an IP address for the unit if the LAN unit isn’t connected to a DHCP server.

22 Installation and Operation Guide 4.3 TCP/IP Communication Software Follow the procedure below to install the TCP/IP communication program in your

Installation and Operation Guide 23 3. Click on the Configuration tag, and check if the TCP/IP is included among the network components list. If the

24 Installation and Operation Guide 4.5 TCP/IP configuration setting Click Start → Settings → Control Panel → Network. Select TCP/IP, and then click

Installation and Operation Guide 25 4.6 Connection Testing With the previous settings, follow the instructions below to ensure whether you have estab

26 Installation and Operation Guide successfully established. Please re-check all the hardware and software installations by repeating sections 4.4

Installation and Operation Guide 27 5. Operation Instructions for the Network The Microsoft Internet Explorer in a PC provides the functions of moni

28 Installation and Operation Guide 5.1 Microsoft Internet Explorer 5.1.1 Connecting the IP camera 1. Start up Microsoft Internet Explorer, and

Installation and Operation Guide 29 Browsing images from the IP camera The images from the IP camera are displayed on the home page when online with

Copyright Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any elec

30 Installation and Operation Guide 5.1.2 Change Video Setting Please follow the steps below to change the image setting through the network as nec

Installation and Operation Guide 31 6. Click on the Day & Night button to enter the Day & Night page. i. Click on the drop-down list to c

32 Installation and Operation Guide 7. Click on the Home button to return to the home page while the new image setting acts on the images to effec

Installation and Operation Guide 33 5.1.3 Change the Network Setting Please follow the steps below to change the network setting through the network

34 Installation and Operation Guide Description of function keys: IP Address: Enter the 4-byte IP Address in the appropriate blank space (the value

Installation and Operation Guide 35  Change the Network Setting — FTP (MJPEG mode only). Please follow the steps below to change the FTP setting vi

36 Installation and Operation Guide  Change the Network Setting — SMTP (MJPEG mode only). Please follow the steps below to change the SMTP setting

Installation and Operation Guide 37  Change the Network Setting — SNTP. Please follow the steps below to change the SNTP setting through the networ

38 Installation and Operation Guide  Change the Network Setting — DDNS. The “Network” page has, on its upper left, the “DDNS” icon. Please follow

Installation and Operation Guide 39 Description of function keys: Enable DDNS Function: Checkmark to activate the function. DDNS Type: Click to open

4 Installation and Operation Guide Table Of Contents SAFETY PRECAUTIONS ...

40 Installation and Operation Guide  Change the Network Setting — PPPoE. The “Network” page has, on its upper left, the “PPPoE” icon. Please follo

Installation and Operation Guide 41  Change the Network Setting —UPnP. The “Network” page has, on its upper left, the “UPnP” icon. Please follow th

42 Installation and Operation Guide  Change the Network Setting — IP Filter The “Network” page has, on its upper left, the “IP Filter” icon. Pleas

Installation and Operation Guide 43  Change the Network Setting —Network Traffic. The “Network” page has, on its upper left, the “Traffic” icon. Pl

44 Installation and Operation Guide 5.1.4 Change the System Setting Please follow the steps below to change the date and time of the system setting

Installation and Operation Guide 45  Change the System Setting — Timestamp. Please follow the steps below to change/add the timestamp through the

46 Installation and Operation Guide  Change the System Setting — Users. Please follow the steps below to change/add the users’ authority through t

Installation and Operation Guide 47  Change the System Setting — Digital I/O. Please follow the steps below to change the Digital I/O through the n

48 Installation and Operation Guide  Change the System Setting — Audio. Please follow the steps below to change the Audio through the network as n

Installation and Operation Guide 49  Change the System Setting — RS485 Setting. Click on the RS485 Setting button on the left side of the “Date and

Installation and Operation Guide 5 5. Operation Instructions for the Network...27 5.1 MICROSOFT INTERNET

50 Installation and Operation Guide  Change the System Setting — Update Firmware. Please follow the steps below to update the firmware through the

Installation and Operation Guide 51  View the Event Logs. Please follow the steps below to view events through the network as necessary. 1. Click

52 Installation and Operation Guide 5.1.5 Change the Application Setting Please follow the steps below to change the application setting through th

Installation and Operation Guide 53  Change the Application Setting — SD Card Application Setting. Please follow the steps below to change the SD C

54 Installation and Operation Guide  Change the Application Setting —SMTP Application Setting (MJPEG mode only). Please follow the steps below to

Installation and Operation Guide 55  Change the Application Setting —Language Setting. Please follow the steps below to change the Language setting

56 Installation and Operation Guide  Change the Application Setting —Record Application Enable Setting. Please follow the steps below to change th

Installation and Operation Guide 57  Change the Application Setting —Record - Schedule. 1. Click on the Application button on the home page to ent

58 Installation and Operation Guide  Change the Application Setting — Alarm Application Enable Setting. Please follow the steps below to change th

Installation and Operation Guide 59  Change the Application Setting — Alarm - Motion Detection. Please follow the steps below to enable changes in

6 Installation and Operation Guide SAFETY PRECAUTIONS All the following safety and operational instructions to prevent harm or injury to the op

60 Installation and Operation Guide 5.1.6 Change the SD card Setting Please follow the steps below to change the SD card setting through the networ

Installation and Operation Guide 61 5.1.7 PPPoE & DDNS Using the PPPoE 1. Install the XDSL software (obtained from your ISP dealer) in your PC

62 Installation and Operation Guide Test: Go to the Internet. 1. Set your PC to enter the Internet. 2. Desktop → IE browser → Enter the IP camera

Installation and Operation Guide 63 5.1.8 The Bandwidth Calculator of the IP camera You can use the calculator to obtain the rough bandwidth through

64 Installation and Operation Guide 6. ADVANCED OPERATION Question 1: How to view the live images of the IP camera via the Microsoft Internet Explor

Installation and Operation Guide 65 ◇Set the recording time (the AVI duration) of the SD card 1. Click on the Application button in the home page in

66 Installation and Operation Guide 3. Choose “ON” from the “PPPoE mode” list to activate it. 4. Enter the Account and the Password which are provid

Installation and Operation Guide 67 7. SPECIFICATIONS ADCIPE3312ICN VideoEdge IP Indoor Mini-dome, 3.3-12mm, clear, NTSC, w/PS ADCIPE3312ICPE Video

68 Installation and Operation Guide LED indicator Network / Power indicator Power requirement DC12V (8.4W) / AC24V / PoE (IEEE 802.af) Temperatu

Installation and Operation Guide 69 APPENDIX 1. –IP camera UPnP How To The most troublesome issue when you setup a LANCam® is that you have no idea

Installation and Operation Guide 7 1. PRODUCT FEATURES 1.1 Product Instructions The VideoEdge IP Indoor Mini-dome ADCIPE3312I is a 3-axis IP dome

70 Installation and Operation Guide Figure 2 Step 2: When Control Panel appears, double-click the Network Connections icon. The Network Connectio

Installation and Operation Guide 71 Figure 5 Step 5: In the Internet Protocol(TCP/IP) Properties dialog box, choose Use the following IP Address to

72 Installation and Operation Guide 2. Install UPnP Packets As described before, Microsoft Windows XP® doesn’t start the UPnP service by default; h

Installation and Operation Guide 73 Figure 10 Step 4: Check UPnP User Interface, and choose OK. See Figure 11. Figure 11 Step 5: When the origi

74 Installation and Operation Guide Step 6: After about one minute the UPnP installation will be done, and choose Finish to close it. See Figure13.

Installation and Operation Guide 75 Figure15 Step 3: Click on the Services icon in the Administrative Tools dialog box. See Figure16. Figure16

76 Installation and Operation Guide Figure17 Step 5: Choose Automatic in the Startup type, and click OK to start it. See Figure18. Figure18

Installation and Operation Guide 77 Figure19 Step 7: Choose Automatic in the Startup type, press the Start button, and click OK to start it. See F

78 Installation and Operation Guide 4. Scan LANCams® through My Network Place After your installation and starting services, the UPnP protocol will

Installation and Operation Guide 79 APPENDIX 2. –The ARP function Setting the IP Address The Ethernet interface on the IP camera has a default IP a

8 Installation and Operation Guide 2. DESCRIPTION OF THE FRONT/REAR VIEW 2.1 The Front View 1. SD CARD slot: This is used for system sof

80 Installation and Operation Guide ARP and ping from UNIX or GNU/Linux: 1. Start a shell 2. Type the following as superuser (root): arp -s <

Installation and Operation Guide 81 APPENDIX 3. –Register as a DDNS member The DDNS（dynamic domain name system） is a function which is provided by an

82 Installation and Operation Guide Figure 2 Figure 3 Click “My Services” to enter the service page. Please click the “Add Host Service” item whic

Installation and Operation Guide 83 Figure 4 Figure 5 All we have to set in this page is the “Hostname” item. You can choose a Sub Hostname as s/

84 Installation and Operation Guide Figure 6

Installation and Operation Guide 85 APPENDIX 4. –MPEG4 Bit Rate Lookup Table of IP camera 1. When frame rate is higher than 15 frames/second (15 is

86 Installation and Operation Guide APPENDIX 5. –PoE Installation Method 1. Provided accessories: IP Indoor Mini-dome Ethernet (CAT5 UTP/Straig

Installation and Operation Guide 87 2. Indoor Mini-dome 3. Power over Ethernet Injector POWER+DATA IN: Connect a CAT 5 RJ-45 st

88 Installation and Operation Guide 4. Connecting the IP Indoor Mini-dome: please take the following steps: Step 1: Insert one end of a Cat 5 Ether

Installation and Operation Guide 89 APPENDIX 6. –FAQ 1. Can the SD card be removed during recording? A：No, it cannot be removed until the recording

Installation and Operation Guide 9 Alarm wiring diagram: 5. VIDEO OUT Connector: The connector provides the unit’s composite video signals to a mo