Arming Monitors
System monitors are armed using a Monitor Arming Code
which identifies the alarm Display method (Single, Block, or
Dual monitors), Queuing method (Sequence or Hold), and the
Clearance method (Instant, Auto, or Manual clear). The
AD1024 Monitor Arming Codes are listed at the right. Refer
to the Appendix, pages A-3 to A-7, for further description of
Alarm Programming and Arming.
Monitors can also be armed using the Monitor menu, page 4-
18. If a monitor block is desired, the Monitor menu must be
used to define and arm the monitors within the block.
The default arming code is Disarmed (DIS) for all monitors.
Note: Monitor Arming is LOCAL only.
To arm a monitor (AD2079 keyboards only):
1. Call the desired LOCAL monitor to be armed.
2. Turn the keyswitch to the PROG position.
3. Select the Monitor Arming Code desired and enter the
code number (1 - 15) on the keypad.
If a Dual display code is selected (13 - 15), when the
first (Hold) monitor is armed, the second (Sequence)
monitor is automatically selected (the next numeric
system monitor) and armed to the second Arm Type.
4. Press the ARM button in the keyboard Monitor group.
The Arm Type (see table at right) is displayed for five
seconds, in the on-screen Status Line.
Example: A monitor is armed for Single/Sequence/Instant
Clear arming code by entering 1 on the keyboard and
pressing the Monitor ARM button, as shown in Figure 3-1.
To disarm a monitor:
1. Call the LOCAL monitor to disarm.
2. Turn the keyswitch to the PROG position.
3. Press the keyboard Monitor OFF button.
To verify the monitor arming at any time, press the keyboard
ARM button. The Arm Type is displayed for five seconds in
the on-screen Status Line. If the monitor has not been armed
or has been disarmed, no Arm Type is displayed.
Notes: DO NOT ARM any monitor output which is used as a
video trunk output to a REMOTE Site.
Monitor arming cannot be changed for any monitor if any
alarm contacts are active in the system.
Monitor Arming Codes (2079 keyboards)
Code Description Arm Type
1 Single/Sequence/Instant Clear SSI
2 Single/Sequence/Auto (after 20 seconds) SSA
3 Single/Sequence/Manual (ACK key) SSM A*
4 Single/Hold/Instant Clear SHI
5 Single/Hold/Auto Clear SHA
6 Single/Hold/Manual Clear SHM A*
7 Block/Sequence/Instant Clear BSI
8 Block/Sequence/Auto Clear BSA
9 Block/Sequence/Manual Clear BSM A*
10 Block/Hold/Instant Clear BHI
11 Block/Hold/Auto Clear BHA
12 Block/Hold/Manual Clear BHM A*
First Monitor Second Mon
Arm Type Arm Type
13 Dual/Hold and Sequence/
Instant Clear DHI DSI
14 Dual/Hold and Sequence/
Auto Clear DHA DSA
15 Dual/Hold and Sequence/
Manual Clear DHM A* DSM A*
16 Disarm monitor DIS
* Manual Clear/Acknowledge is always enabled.
The Manual Clear/Acknowledge feature can be enabled or
disabled for any Instant or Auto Clear arming code. This must
be done after a monitor is armed with an arming code. When
enabled, the letter “A” is displayed after the Arm Type in the
on-screen Status Line (e.g., SSI A). When disabled, the letter
“A” is not displayed after the Arm Type.
To enable/disable Manual Acknowledge for Instant or Auto:
1. Call the desired LOCAL monitor.
2. Turn the keyswitch to the PROG position.
3. Enter one of the following code numbers on the keypad:
17 - to enable Manual Clear/Acknowledge
18 - to disable Manual Clear/Acknowledge
4. Press the Monitor ARM button.
3-6
NON-MENU PROGRAMMING AD1024
(96 paginas)
(264 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales